GNU/Linux man pages
Livre :
Expressions régulières,
Syntaxe et mise en oeuvre :
GNU/Linux |
Debian 6.0.0(Squeeze) |
|
 |
recode(1) |
 |
recode − converts files between character sets
recode [OPTION]... [ [CHARSET] | REQUEST [FILE]... ]
Free ’recode’ converts files between various character sets and surfaces.
If a long option shows an argument as mandatory, then it is mandatory for the equivalent short option also. Similarly for optional arguments.
Listings:
−l, −−list[=FORMAT]
list one or all known charsets and aliases
−k, −−known=PAIRS
restrict charsets according to known PAIRS list
−h, −−header[=[LN/]NAME]
write table NAME on stdout using LN, then exit
−F, −−freeze−tables
write out a C module holding all tables
−T, −−find−subsets
report all charsets being subset of others
−C, −−copyright
display Copyright and copying conditions
|
−−help |
display this help and exit |
−−version
output version information and exit
Operation
modes:
−v, −−verbose
explain sequence of steps and report progress
−q, −−quiet, −−silent
inhibit messages about irreversible recodings
−f, −−force
force recodings even when not reversible
−t, −−touch
touch the recoded files after replacement
−i, −−sequence=files
use intermediate files for sequencing passes
−−sequence=memory
use memory buffers for sequencing passes
−p, −−sequence=pipe
use pipe machinery for sequencing passes
Fine tuning:
−s, −−strict
use strict mappings, even loose characters
−d, −−diacritics
convert only diacritics or alike for HTML/LaTeX
−S, −−source[=LN]
limit recoding to strings and comments as for LN
−c, −−colons
use colons instead of double quotes for diaeresis
−g, −−graphics
approximate IBMPC rulers by ASCII graphics
−x, −−ignore=CHARSET
ignore CHARSET while choosing a recoding path
Option −l with no FORMAT nor CHARSET list available charsets and surfaces. FORMAT is ’decimal’, ’octal’, ’hexadecimal’ or ’full’ (or one of ’dohf’). Unless DEFAULT_CHARSET is set in environment, CHARSET defaults to the locale dependent encoding, determined by LC_ALL, LC_CTYPE, LANG. With −k, possible before charsets are listed for the given after CHARSET, both being tabular charsets, with PAIRS of the form ’BEF1:AFT1,BEF2:AFT2,...’ and BEFs and AFTs being codes are given as decimal numbers. LN is some language, it may be ’c’, ’perl’ or ’po’; ’c’ is the default.
REQUEST is SUBREQUEST[,SUBREQUEST]...; SUBREQUEST is ENCODING[..ENCODING]... ENCODING is [CHARSET][/[SURFACE]]...; REQUEST often looks like BEFORE..AFTER, with BEFORE and AFTER being charsets. An omitted CHARSET implies the usual charset; an omitted [/SURFACE]... means the implied surfaces for CHARSET; a / with an empty surface name means no surfaces at all. See the manual.
If none of −i and −p are given, presume −p if no FILE, else −i. Each FILE is recoded over itself, destroying the original. If no FILE is specified, then act as a filter and recode stdin to stdout.
Written by Franc,ois Pinard <pinard@iro.umontreal.ca>.
Report bugs to <recode-bugs@iro.umontreal.ca>.
Copyright
© 1990, 92, 93, 94, 96, 97, 99 Free Software
Foundation, Inc.
This is free software; see the source for copying
conditions. There is NO warranty; not even for
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
The full documentation for recode is maintained as a Texinfo manual. If the info and recode programs are properly installed at your site, the command
info recode
should give you access to the complete manual.
|
recode(1) | |